Knowing how to treat your door is a very important factor in maximising its performance. Bespoke doors will last considerably longer when the correct treatments are applied.
1. Do not stand new doors against an outside wall (in the house) as the cold wall can make them twist or bow etc.
2. Do not place new doors in a location where new plasterwork has been carried out within the last two or three weeks.
3. All forms of moisture or the lack of it, rain, condensation and even humidity have a critical bearing on the well-being of your door,especially patterns that have solid timber panels.
We take great care to supply you with what are probably the finest doors available and we certainly derive no pleasure whatsoever from the stressed and sorry state we sometimes see some doors reduced to owing to the ignorance and abuse to which they have been subjected. After doors have left our premises we have no control over the conditions to which they are exposed and in the interests of the continued validity of our guarantee we cannot stress too strongly the importance of observing the advice contained throughout this site.
Every effort is made to ensure that the moisture content levels of our doors are in accordance with BS1186 part one when they enter and leave our warehouse or workshop. This provides for Exterior doors to be in the range of thirteen to nineteen per cent and Interior doors ten to fourteen per cent. For this reason, it is vital that the moisture levels are retained and Exterior doors are not used for interior and vice versa.
Pictured above: Bespoke Andria Oak Panelled and Bespoke Forli Dark Grey Flush
We do hope that you take on board the advice that we offer within this site and avoid the possibility of becoming dissatisfied with the appearance and performance of your door.
Decorating tip: Please make sure that no water based decorating products are used on any door that is veneered, Some of our External & Internal doors and frames may be over-veneered to provide a better quality finish and greater stability, please treat the advice offered above seriously, if in doubt please ask for our advice.
To decorate any door, use the general directions above and the detail below for Exterior or Interior Doors and Frames including veneered, solid timber or bespoke products.
1. For a painted finish, use a primer, followed by two layers of an undercoat, and then finish with a minimum two top coats. YOU MUST ONLY USED OIL BASED OR SOLVENT BASED PAINT THAT IS MICROPOROUS.
2. Remember to sand the doors down lightly in between each coat.
3. For a stain finish: YOU MUST ONLY USED OIL BASED OR SOLVENT BASED STAIN THAT IS MICROPOROUS
4. Again, remember to sand the doors down lightly in between each coat.
5. Please make sure that no water based decorating products or Wax or Danish Oil of any type are used on any door that is solid OR veneered.
6. Exceptions; Interior doors can have a varnish used but again it must be solvent based or oil based.
If in doubt please ask for our advice.
Pictured above: Bespoke Victorian Oak Panelled and Bespoke Shaker 4L White Primed Glazed
We recommend that before attempting to fit your door, you first take care to select the finish you require, check with the manufacturer if necessary, that it will give a complete and lasting seal between all component parts.
Many well-known brands of wood finish which may provide excellent surface protection fail to provide this vital element and may permit the passage of moisture around panel grooves.
As mentioned above, please avoid the use of varnish or polyurethane-based products and also Danish Oil on External or Internal veneered doors & frames, solid timber doors & frames or bespoke doors & frames and look for a brand that gives protection against the bleaching-out effect of the suns ultra-violet rays. Use polyurethane finish on veneers or ply doors only; this type of varnish is also suitable for most interior solid timber doors.
Immediately upon receipt sand the door down lightly with fine glass-paper (grade 200) or wire wool in the direction of the grain to remove nibs, small chips, scratches and finger marks.
We know we are stating the obvious but do not allow any sandpaper to make contact with any glass surfaces.
Dust down thoroughly and apply at least three coats of your selected wood care product inside and out including at least one finishing coat to all surfaces before installation, including glazing rebates and all around glazing beads, be sure to follow the manufacturer's instructions.
Remember, the door needs to be coated equally inside and out to allow a balanced movement of any moisture.
If you have any questions, you can easily contact us via info@directdoors.com (or call us on 01968 671 681) and we will be happy to help.